Jeld-wen JII036 Custom Swinging Screens Bedienungsanleitung PDF herunterladen

Note! Do not over tighten screws and strip out mounting screw holes.

HEAD Z-BAR INSTALLATION

Verify the head is straight

and level. If not, washers

can be placed behind

z-bar mounting holes as

necessary. Use a glue stick

to hold washers in place.

Center the head z-bar

between the door jambs.

Drive one of the supplied

#8 x 1" self-tapping

Phillips at-head screws

through the pre-punched

hole in one end. Continue

driving screws through the rest of the holes.

HINGE SIDE Z-BAR INSTALLATION

1. Verify door hinge side jambs are straight and plumb. If not, washers can

be placed behind z-bar mounting holes as necessary. Use a glue stick to

hold washers to the z-bar.

2. Pivot z-bar 90° open

from screen assembly

and place into door

frame. While holding

z-bar against door

jamb, lift screen

assembly up until snug

against the head z-bar.

3. Using the supplied #8 x

1" self -tapping Phillips

at-head screws,

position a screw in the

top of the uppermost

pre-punched hole and

drive until secure.

Continue down, driving

screws through the

remaining pre-punched

holes.

4. If installing double

screens, repeat steps for

the other screen.

5. Close the screen

assembly(ies) and check for uniform gap between the door screen

assembly and head z-bar. For double units check for uniform 1/2" to

9/16" gap between the two screens. If necessary, remove and add or

remove washers as needed and reinstall.

INSTALLATION INSTRUCTIONS

for Custom Swinging Screens (JII036)

•#2 Phillips

screwdriver

•#3 Phillips long bit

•Hacksaw or le

•Pencil

•Regular slotted

screwdriver

•Power drill with bits

•Level

•Tape measure

•Utility knife or

scissors

•Masking tape

•Washers

•Glue stick

Determine if the unit is a single unit entry door or double unit and if it is a

wood or aluminum clad frame. For primed or clad units, determine which

door screen will be mounted on the active side of the opening. The active

side is the door screen which will be used for passage through the door

unit while the passive side is left closed.

NEEDED TOOLS & MATERIALS

LATCH SIDE Z-BAR INSTALLATION

Note! Applies to single entry units only, double screen units skip this step

and will install an astragal in the next step.

1. Close the screen

assembly and check

for a uniform gap of

1/8" - 1/4" between the

screen latch stile and

the door frame. Place

washers behind the

z-bar mounting holes

if needed. Use a glue

stick to hold washers in

place.

2. Re-open the screen

assembly approximately

90° and place the latch

side z-bar against the

door frame latch side

jamb and up against

the underside of the

head z-bar. Install in

the same manner as the

hinge side. Close the

door screen assembly

and re-check for a

uniform gap between

the screen perimeter

and the latch side z-bar.

If necessary, remove

and add or remove

washers as needed and

reinstall.

DOUBLE UNIT ASTRAGAL INSTALLATION

1. Align the astragal on

the passive screen

side stile with the top

of the screen frame

and against the inside

ange.

2. Hold in place and drive

one of the supplied

#8 x 1" self-tapping

Phillips at-head screws

through the top hole

and into the screen

frame.

3. Hold the astragal against the inside ange and install the remaining

screws. If the bottom end of the astragal rubs on the door sill, remove

and trim as needed.

Head

Jamb

#8 x 1" screw

#8 x 1"

screw

#8 x 1"

screw

Optional

washer

Door

frame

Optional

washer

Head

Z-Bar

Hinge

Z-Bar

Hinge

Z-Bar

Door

frame

Screen

assembly

Screen

assembly

1/8" - 1/4"

gap

Head

#8 x 1"

screw

Optional

washer

Jamb

Z-Bar

Passive

screen

side stile

Astragal

1 2 3

INSTALLATION INSTRUCTIONS 1

Inhaltsverzeichnis

Seite 1 - INSTALLATION INSTRUCTIONS

Note! Do not over tighten screws and strip out mounting screw holes.HEAD Z-BAR INSTALLATIONVerify the head is straight and level. If not, washers can

Seite 2

SILL EXPANDER ADJUSTMENTUsing a utility knife, trim the exible ap so that it will just touch at both ends when the screen assembly is closed. The e

Seite 3

Kommentare zu diesen Handbüchern

Keine Kommentare

Jeld-wen JII036 Custom Swinging Screens Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für Zuhause Jeld-wen JII036 Custom Swinging Screens herunter. JELD-WEN JII036 Custom Swinging Screens User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für Zuhause Jeld-wen JII036 Custom Swinging Screens