Jeld-wen JCM004 Interior and Exterior Door Slabs and System Bedienungsanleitung PDF herunterladen

FINISHING AND REFINISHING INSTRUCTIONS

for Interior and Exterior Door Slabs and Systems (JCM004)

The information contained herein is provided solely for informational and/or educational purposes. JELD-WEN disclaims any and all liability associated with the use and/or

provision of this information. Any reliance upon the information or advice is at the risk of the party so relying.

property laws. All trademarks, service marks, logos and the like (whether registered or unregistered) are owned or controlled by JELD-WEN, inc. or others.

Unauthorized use or duplication of JELD-WEN intellectual property is prohibited.

JELD-WEN reserves the right to change product specications without notice. Please check our website, jeld-wen.com, for current information.

Read all instructions thoroughly before beginning. This is a guideline

for painting and nishing exterior and interior doors. JELD-WEN cannot

evaluate all available paints, stains, or application requirements. Consult

a paint professional or a local paint department/store for coatings

best suited to the project. Select top quality nishes and follow all

manufacturers' instructions.

Finish all six surfaces (both sides and edges) of the door slab, including

cutouts for hardware (if hinges are installed on an interior door slab,

do not remove them), as well as the frame and the brickmould or other

trim to ensure proper protection from the elements. The sweep on the

bottom of exterior doors needs to be sealed on both ends with exterior

silicone sealant and should not be painted or stained. The sweep should

not be removed as paint or stain application to the rail underneath is not

recommended. Failure to nish the door slab as instructed may result in

the denial of warranty claims for operational or performance problems.

IMPORTANT!

• Steel and berglass door slabs MUST be nished within thirty (30)

days of purchase.

• Factory primed wood doors (molded, ush, custom carved, stile and

rail) MUST be nished within fourteen (14) days of purchase.

• Raw, un-primed wood doors (molded, ush, custom carved, stile and

rail) MUST be nished within SEVEN (7) days of purchase.

• Finish wood frames in the same manner as the slab.

• Vinyl components do not require nishing.

• Renish products when the nish cracks, splits or becomes dull.

NEEDED MATERIALS AND TOOLS

When preparing to nish doors, consider the materials and tools required for

the entire project. Listed below are some common items needed to properly

nish doors. Not all materials and tools will be required for every job.

(08/14)

BASIC FINISHING RECOMMENDATIONS - CONTINUED

• Allow doors to acclimate to local conditions for at least 24 hours

before nishing.

• Remove all hardware (except hinges from an interior door slab) and

mask off glass, weatherstrip, and the door sweep (on the bottom of

exterior slabs).

• Finish in dust free area away from direct sunlight.

• Finishing is easier if the slab is in a horizontal, at position on a

padded surface. This is not required and the slab may be nished in

any position, however, do not stand an exterior slab on the sweep

(the weatherstrip on the bottom of the door) as damage may result.

• If nishing an exterior slab, seal both ends of the sweep (weatherstrip

on the bottom) with an exterior grade silicone.

• If nishing a slab with a glass insert, inspect for sealant that may have

squeezed out onto the glass or door. Carefully score excess sealant (do not

scratch glass) with a utility knife (stainless steel blade) and remove with a

plastic putty knife.

• If nishing a slab with a glass insert, follow the glass manufacturer's

instructions on the glass insert frame label.

• Door must be clean and dry before nishing.

• Test your nish prior to application in a discreet location.

• Apply nish materials in multiple light coats instead of fewer heavy coats.

• If painting grained or textured doors, too many coats will diminish

the wood grain texture.

CHOOSE FINISHING MATERIALS

• If the door is exposed to direct sunlight, dark colored nishes may

fade or deteriorate quickly and increase maintenance. See our

Appropriate Protection document at www.jeld-wen.com in the

Product Support section under Care and Maintenance for more

information on color choice.

• Use a good quality primer and paint, or wood sealer and stain.

We recommend using one manufacturer's products to ensure

compatibility. Follow all manufacturers’ application instructions.

• If choosing an oil or solvent based paint, consult with a paint

professional on the best product (usually quick drying) for the job.

• If staining berglass doors, for the best results, we recommend using our

Stain Kit. If not possible, use only a professional quality, heavy body or

highly viscous exterior gel stain. Note: Once Architectural berglass doors

are stained, it is very difcult to change the color. Always test the color

in an inconspicuous area to determine if the color is acceptable before

staining the entire door.

• Use only exterior solid color stains on wood surfaces exposed to

sunlight because their high concentration of pigments protects wood

against damage. The natural wood color and grain is obstructed,

but the wood texture is retained. These stains provide minimum

protection against water or dirt protection, so a polyurethane top

coat must be used.

• Finish with coatings that are resistant to water, wear, heat, solvents

and chemicals. Without these characteristics, the nished product

may deteriorate, compromising its integrity.

• Use a topcoat containing UV inhibitor. Use exterior nishing products

on all exterior surfaces as well as for interior surfaces still exposed to

sunlight to provide extra protection and durability.

Needed Materials and Tools:

• Safety glasses and rubber

gloves

• Screwdrivers

• Power drill

• Hammer

• Punch

• Utility knife

• Plastic putty knife

• Hand block sander

• Foam brush

• Paint brush

• Sprayer

• Vinegar and water

• Denatured alcohol

• Wood block

• Masking tape

• Sandpaper - 150-220 grit or

ner

• Pre-stain conditioner if

staining wood

• Clean rags

• Cheesecloth

• Polyurethane

• Stain Kit (Fiberglass Doors)

• Paint or stain (see instructions

for each door type for specic

recommendations)

• Paint thinner or mineral spirits

(for clean up)

• Tack cloth

• 0000 Steel wool

BASIC FINISHING RECOMMENDATIONS

• Wear safety glasses for eye protection, and rubber gloves to prevent

soiling the door with oil from hands.

1 2 3 4

Inhaltsverzeichnis

Seite 1

FINISHING AND REFINISHING INSTRUCTIONSfor Interior and Exterior Door Slabs and Systems (JCM004)The information contained herein is provided solely for

Seite 2

FINISHING AND REFINISHING INSTRUCTIONSfor Interior and Exterior Door Slabs and Systems (JCM004)2Use the table below to nd your product and desired n

Seite 3

FINISHING AND REFINISHING INSTRUCTIONSfor Interior and Exterior Door Slabs and Systems (JCM004)3Doors to be Painted Doors to be StainedWood (Authentic

Seite 4

FINISHING AND REFINISHING INSTRUCTIONSfor Interior and Exterior Door Slabs and Systems (JCM004)4Please visit jeld-wen.com or call us at 1-800-535-3936

Kommentare zu diesen Handbüchern

Keine Kommentare

Jeld-wen JCM004 Interior and Exterior Door Slabs and System Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für Zuhause Jeld-wen JCM004 Interior and Exterior Door Slabs and System herunter. JELD-WEN JCM004 Interior and Exterior Door Slabs and Systems User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für Zuhause Jeld-wen JCM004 Interior and Exterior Door Slabs and System