Jeld-wen JII106 Pre-Hung Exterior Entry Doors Bedienungsanleitung PDF herunterladen

INSTALLATION INSTRUCTIONS

for Pre-Hung Exterior Entry Doors (JII106)

Newer construction methods have led to an increase in air and water

tightness in buildings. This frequently leads to negative air pressure

inside the house, which can draw water through very small openings.

Our installation method seals the door to the weather barrier

(typically building wrap) and uses a sill pan to capture and drain

incidental storm water from under the door.

Thank you for selecting JELD-WEN

products. Attached are

JELD-WEN’s recommended installation instructions for Exterior

Wood, Steel, and Fiberglass Pre-Hung Doors. Read these

instructions thoroughly before beginning. They are designed to

work in most existing applications; however, existing conditions

may require changes to these instructions. If changes are needed,

they are made at the installer’s risk. For installations other than

indicated in these instructions, contact a building professional.

Not all exterior door types may be installed into every wall condition

in all areas. See our Appropriate Protection document for overhang

requirements and our Additional Requirements document for Fire

Doors at www.jeld-wen.com/resources. Consult your local building

code ofcial (or Authority having Jurisdiction) for applicable building

codes and regulations. Local building code requirements supersede

recommended installation instructions.

Please Note! Any exterior door installation where the sill is higher than

35 feet above ground level or into a wall condition not specically

addressed in these instructions must be designed by an architect or

structural engineer. Failure to install square, level and plumb and on a

at surface (without twist or warp) could result in denial of warranty

claims for operational or performance problems.

Note to Installer: Provide a copy of these instructions to the building

owner. By installing this product, you acknowledge the terms and

conditions of the limited warranty as part of the terms of the sale.

GLOSSARY

Backer Rod (backing material)

A material (e.g. foam rod), placed into a joint primarily to control the

depth of the sealant.

Buck

A wood framework attached to the masonry inside a window or a door

rough opening.

Door System/Pre-Hung Door

A pre-cut and assembled unit consisting of a door slab (prepared for the

locking or passage hardware) hung on hinges in a wood or metal frame.

Hinge Jamb

The side of the jamb on which the hinges of a door are installed.

Rough Opening

The framed opening in a wall where a door is to be installed.

Security Plate

A metal plate pre-installed into the frame of a pre-hung door. It is

designed to provide extra strength and stability from a forced entry

attempt by allowing the latch of the door to rest inside it when the

door is closed.

Shiplap

The layering method in which each layer overlaps the layer below it so

that water runs down the outside.

Shipping Strap

Small, metal or plastic clips that come attached to a door system.

These clips help keep a door slab closed and aligned before and during

installation.

IMPORTANT INFORMATION AND GLOSSARY

Estimated Install

Time for New

Construction

First Time: 4.0 hr.

Experienced: 2.5 hr.

Professional: 1.5 hr.

8 4

7 5

LANDINGS

These instructions

cover two sill

conditions: the

step-down landing

and the continuous

slab landing. The

installation methods

vary slightly between

landing types.

Please allow sufcient time to properly prepare the rough opening,

install the entry door, and ensure its proper operation.

Step-Down Landing

Continuous

Slab

Landing

Sidelight

A xed, usually rectangular window placed on either side of a door.

Sill Pan

A three-sided box made of sheet material. The door sill sits inside the sill

pan in the rough opening. It is designed to catch water that inltrates

into the rough opening and divert it to the outside.

Strike Jamb

The side of the jamb that makes contact with the latch on a door slab.

1 2 3 4 5 6 7 8

Inhaltsverzeichnis

Seite 1 - INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONSfor Pre-Hung Exterior Entry Doors (JII106)Newer construction methods have led to an increase in air and water tightness in bu

Seite 2

INSTALLATION INSTRUCTIONS for Pre-Hung Exterior Entry Doors (JII106) 2FULLY SHEATHED WALL CONSTRUCTIONThe wall framing is covered by sheathing and the

Seite 3

INSTALLATION INSTRUCTIONS for Pre-Hung Exterior Entry Doors (JII106) 3REMOVE PACKAGINGRemove shipping materials such as corner covers, shipping blocks

Seite 4 - INSPECT ROUGH OPENING

INSTALLATION INSTRUCTIONS for Pre-Hung Exterior Entry Doors (JII106) 46. For continuous slab, cut across the folding line.7. Fold the three back sid

Seite 5 - PREPARE BUCK

INSTALLATION INSTRUCTIONS for Pre-Hung Exterior Entry Doors (JII106) 56. Cut two pieces of self-adhesive ashing 6" wide by the sill pan width

Seite 6 - INSTALL DOOR

INSTALLATION INSTRUCTIONS for Pre-Hung Exterior Entry Doors (JII106) 66INSTALL DOORWarning! To avoid injury, use at least two people to install. Adequ

Seite 7 - INSTALL DOOR - CONTINUED

INSTALLATION INSTRUCTIONS for Pre-Hung Exterior Entry Doors (JII106) 74. If installing a door with a metal frame and adjustable T-Strike, place A ove

Seite 8 - COMPLETE INSTALLATION

INSTALLATION INSTRUCTIONS for Pre-Hung Exterior Entry Doors (JII106) 8FIRE DOOR HINGESDo not remove or paint over any re labels. Please see our separ

Kommentare zu diesen Handbüchern

Keine Kommentare

Jeld-wen JII106 Pre-Hung Exterior Entry Doors Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für Zuhause Jeld-wen JII106 Pre-Hung Exterior Entry Doors herunter. JELD-WEN JII106 Pre-Hung Exterior Entry Doors User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für Zuhause Jeld-wen JII106 Pre-Hung Exterior Entry Doors